C4D插件 抽象多边形镂空插件汉化版 Trypogen 1.1

C4D插件 抽象多边形镂空插件汉化版 Trypogen 1.1    [复制链接]

C4D插件 2018-04-12 13:37 发布

版权归原作者所有,仅供交流学习,禁止商业使用!
C4D插件
作用分类: 特殊效果 » 镂空
插件分类: 插件
使用教程: 含教程
支持(高版本请自测): R15 R16 R17 R18 R19 
支持语言: 英文 汉化 
支持系统: PC MAC 
出现位置: 插件菜单 
检索码: -


1280.jpg

870505aceee5e54658.png
C4D插件 抽象多边形镂空插件汉化版 Trypogen 1.1

Smooth Subdivision rounds your geometry by adding more polygons.

Linear Subdivision is executed before Smooth subdivision and is used to emphasize edges.

Curved Subdivision adds folds and creases.

Spiky Subdivision creates thorn from original points. It is recommended to keep its value lower than 2. An overall size of extruded spikes can be altered by changing the thickness value.

Points Limit specifies the maximum number of points received from original geometry. Points value simply displays the number of points and can not be changed directly. It is recommended to use Reduction value in order to decrease the number of points below the specified limit in order to allow trypogen generating new polygons. If this value higher than a specified limit, new geometry will not be generated unless you reduce the number of points.

Reduction value reduces the number of polygons.
By reducing the number of polygons, angle between these elements is growing, so it is to use this parameter in combination with Angle Limit.

This option works in the same way as the Phong angle. Use this setting to define the angle to which two neighboring surfaces should be connected.

This setting will define how far apart object points can lie to be welded in order to reduce the number of polygons. Unlike reduction value, It can be used to remove only unnecessary small details from your geometry while larger polygons will not be affected.

Depth defines a distance between an edge of the original polygons and the corresponding edge of the inner elements. Negative value gives inverted results.

Variation gives a percentage value for the variation of the depth. Its slider is limited to 100, however, you can push this value up to 200.

Enter a Thickness value here to give polygons volume. The volume is achieved by extruding the surfaces in the direction of their surface Normals. To reverse the direction of the extrusion, enter a negative value.

Trypogen 1.1

Smooth Subdivision通过添加更多的多边形来圆化您的几何图形。

Linear细分在Smooth细分之前执行并用于强调边缘。

曲线细分增加了褶皱和折痕。

Spiky细分从原始点创建刺。建议保持其值低于2.通过改变厚度值可以改变挤出尖刺的整体尺寸。

分数限制指定从原始几何体接收的最大点数。点值仅显示点数,不能直接更改。为了让trypogen生成新的多边形,建议使用Reduction值来减少低于指定限制的点数。如果此值高于指定限制,则除非您减少点数,否则不会生成新的几何图形。

减少值减少了多边形的数量。
通过减少多边形的数量,这些元素之间的角度越来越大,因此将这个参数与角度限制结合使用。

此选项与Phong角度相同。使用此设置可定义两个相邻曲面应连接的角度。

该设置将定义物体点可以放置多远,以便减少多边形的数量。与缩小值不同,它可以用于从几何体中移除不必要的小细节,而较大的多边形不会受到影响。

深度定义原始多边形的边缘与内部元素的相应边缘之间的距离。负值给出倒转结果。

变化给出深度变化的百分比值。它的滑块限制为100,但是,您可以将此值提高到200。

在此处输入厚度值以给出多边形的体积。通过将表面按照其表面法线方向挤出来实现体积。要反转挤出的方向,请输入负值。
C4D多边形创意镂空曲面平滑插件中文汉化版 Trypogen 2.0 For C4D 支持R16-25


C4D插件 抽象多边形镂空插件汉化版 Trypogen 1.1 
关闭

菜鸟C4D推荐上一条 /9 下一条

菜鸟C4D与你一起从零开始!
十年专注C4D学习

( 浙ICP备13033195号-2 )Copyright   ©2013-2024  Powered by©Discuz!  技术支持:cainiao    

|网站地图